Idler hub for 3.5k axle, 5 on 5" bolt pattern Does not include: bearings, races, seal, lug nuts, & grease cap.
Rated line pull 9500 lbs Rope wire 21/64 x 95' Remote 12' Rubber sealed hand-held
Top-wind Jack Tounge Mount 5000lb capacity Swivel Pipe Mount Works with 140418 pipe This is that same jack that is commonly used as support jacks on the back of the Car Hauler and Buggy Hauler PJ Trailers. This is the standard tongue jack that is put on most U6, U7, U8, C4, and C5 PJ Trailers.
Used on the standard deckover trailers Width: 22" Length: 30" Thickness: ¼ "
Used on the Low-Pro Deck over trailers Width: 22" Length: 23" 1/4" thick
Mudflap (Single) 13" Wide 27" Long ¼ " Thick This mudflap is used on DS and 96" wide F8 trailers.
Mud flap for FS trailers and others that are equipped with single wheels. The dimensions are 16" wide and 27" long.
Bi Fold Gate for Black U7 trailers This gate is 4 ft. long when extended but only rises 25" above the floor when in stowed position for reduced wind drag This gate is a direct replacement for any of our 76" wide gates with no additional mounting hardware needed. Powder coated Black.
Gate Bi-fold 83" U8 reg side
Quality 3.5k Includes: 111200 x 1 Hub Drum Only 84550 EZ Lube 3.5k 111500 x 1 Bearing 1.0625" ID L44649 Outer #84 111503 x 1 Bearing 1.3785" ID Inner 3.5k 111518 x 1 Seal for #84 1.719" x 5.565" Dbl Lip 111525 x 1 Grease Cap 1.98" A-Lube 3.5k #84 111532 x 5 Lug Nut 1/2"-20x60 degree cone
10" passenger's side electric brake for most brands of 3500 # axles
Allows quick/easy replacement of worn or damaged safety chains Weld on application Used with 3/8" chain This is the size typically used on PJ gooseneck trailers.
Hitch Pin 5/8"x3"
This ramp is used on most C4 and C5 trailers. Each ramp is rated for 10,000 lbs These ramps will have the hook welded on the inside edge of the main channels 60" long 13" wide 3" channel supports Black Powder Coat 59 lbs each Sold individually -***This ramp is very similar to the 160205. The only difference is the width. This one is just about an inch wider. They may not fit well in a ramp pocket that was built for the narrower ramp.
1.5" x 1.5" square tube stabilizer leg for Dump Trailers 30" long Prevents PJ dump trailers from lifting up on the tailgate of the pickup when loading equipment Can be adjusted up all the way when not in use Black powder coat Sold by the each Does not include hitch pins. 150300 Sold individually, takes quantity 2 per trailer
Fits PJ 3 3/4" ID Stake Pockets D-ring rated at 11,780 lbs Can be moved in seconds with no tools Black Powder Coat Finish Includes hitch pin Not for use on dump trailer stake pockets This Stake Pocket D-rings does not fit most C 4 Car haulers or Utility Trailers 5" tall from the bottom of the channel to bottom of the flange The channel is approximately 3 5/8" wide 1/2" diameter d-ring The channel depth is 1 1/2" deep 3 1/2" from bottom of flange to the top of the hole Flange length 4 3/8", flange width 1 3/4 in 1 3/4" from top of hole to the bottom of the d-ring
This is a portable spare tire mount that fits most trailers with standard size stake pockets (3.75" ID) Can be used with 1/2" or 9/16" stud Drive-in wheel studs sold separately. This mount can be easily moved around from stake pocket to stake pocket by simply removing a bolt. 3.5" spare tire base Square tubing offsets the mounting plate 7.5" from the trailer Black powder coat finish ***This mount does not fit in a dump trailer stake pocket.
Silver-colored safety chain typically found on utility trailers with "s" hook and keeper.
This is the 9/16" stud, used in our spare tire mount as of 11/2010.
used on our 14k bumper pull trailers rated at 18k per chain and feature clevis hooks with keepers for worry free attachment.
Safety pin for bulldog 2B 3B AND 4B style couplers.
Blue artic technology cable that stays flexible in cold weather Front harness that fits domestic built PJ bumper pull trailers Connects the junction box to tow vehicle Molded sealed plug Two contacts for each blade Heavy duty industrial grade durable trailer harness 84" length 7 blade RV Style plug
Get a Quote
Please enter your contact information and one of our representatives will get back to you with more information.