4" O.D. oil cap used for 10k heavy duty -15k Dexter axles .
Dexter Heavy Duty 10K &12K & 15K Complete oil cap with center plug and o-ring This will fit the pre-2010 10k general duty axle also WILL NOT the new one piece 10K GD hub and drum This will fit just about all PJ 12K Dexter axles, PJ 15K Dexter axles, and also DISC BRAKE 10k Dexter axles 111608x1; 111609x1 & 111607x1
Does NOT include o-ring or plug.
This Plug fills the center hole in the plastic oil caps made by quality running gear and Dexter.
Alko part # K363587
Includes: oil cap, o-ring and plug
Bulldog Jack Tpwnd 7K 4 & 5" Channel Utility will work with both 4 & 5" with 4 hole channel bracket
This rack is designed to mount to the PJ Ready Rail side rails and can be used for several purposes. It can be used to haul pipe, tubing, lumber, ladders, etc. The racks are sold individually. Most applications will require 2 or 3 racks per trailer side. Each rack ships with 3 mounting bolts and nuts. 1 tie off under each rack 45"height x 2" wide x 1" and extends out 9 ½ "
This is the pump that will work on all Hydraulic dumps, tilts, jacks, dovetails, that are made by PJ. Since @2014 the only trailers these are used in are the TDD and the TD models. In 2014 we started using the same pump with the smaller reservoir for all other applications. 6 Quart Plastic Offset Reservoir 12V DC, (2) Terminal, Electric Motor 12V DC Heavy duty plastic start solenoid switch /100 amp Cartridge relief valve, Adjustable set 4W2P Spool type cartridge soleniod valve 10V DC #8 Cylindrical coil w/ Dual spade NC 2-WAY and P.O.C in 4-WAY Cartridge valve Secondary relief valve w/ side exhaust ports. Set at 1500 PSI SAE #6 (9/16-18) Plastic shipping plug Pressure loaded gear pump (0.1324 IN³/R) KTI 3/4 NPT 40 Micron air breather 2 Button 4-Wire Remote Pendant w/ Cylindrical Quick Disconnect 15' Cord Warning Label Tag, Yellow, Torgue Spec RVSAE6-30 @ 1500 PSI. Perfect replacement pump for 12VDC remotely controlled hydraulic systems Perfect for Dump Trailers - Lift Gates!! Length 21.5" x Height 8" x Width 8"
legal for use on trailers less than 80" wide.
Taillight Stud Mount Square RH
Backup Light 6" Oval LED
This is an Oval red tail tight that mounts on a flat surface. Has no provision for quick connect (hardwire installation only) Has holes in flange for screws.
This is an AMBER oval LED lite that can be used as a clearance marker and turn signal (mid mount turn signal)
These fenders are sold with the light brackets/gussets loose. Photo for reference only.
Kingpin, 2" GN Adapter Round Pipe
Jack, 5K Pipe Mount Sidewind
Spring, R.H. Carhauler Ramp
Spring, L.H. Carhauler Ramp
Spring for Fold-up Gate, L or R
Binder, lever chain 3/8"
Gate Latch Handle Pin Mx
Spring for Gate Latch, 4"x5/8"
Slam Latch T-Handle - Sidemount Box
Slam Latch for Top-lid Toolbox Keys included
Kit Includes: Hub/Drum Kit quality running gear 5.2k 6 lug Complete 111201 x 1 Hub Drum Only 42655 EZ Lube 111501 x 1 Bearing 1.25" ID Bolt Outer 5.2K 111504 x 1 Bearing 1.75" ID Inner #42 Outer #99 111519 x 1 Seal for #42 2.25 x 3.376 111526 x 1 Grease Cap 2.44" A-Lube 5.2K #42 111532 x 6 Lug Nut ½ -20 x 60⁰ Cone
Get a Quote
Please enter your contact information and one of our representatives will get back to you with more information.